READ ONLY FORUM: m23 :: makes software distribution easy The m23 discussion forum    FAQ   Search   Memberlist   Usergroups   Register   Profile   Log in to check your private messages   Log in  dhcp error          READ ONLY FORUM: m23 :: makes software distribution easy Forum Index -> Problems with the server / Serverprobleme View previous topic :: View next topic   Author Message gml Guest Posted: Thu Sep 02, 2004 14:02    Post subject: dhcp error during the server start, dhcpd3 said that it's impossible to run. I read the /etc/dhcp3/dhcp.conf it's the default file of configuration. Where is the file generated by installation ? I use the last stable and developpement version and I've same problem with two. an idea ? Back to top gml Guest Posted: Thu Sep 02, 2004 14:55    Post subject: info the dhcpd conf file is : /etc/dhcp3/dhcpd.conf during the installation, a message says that rm don't remove dhcpd.conf because the file doesn't exist. help me please Back to top Hauke Joined: 02 Mar 2003 Posts: 1072 Posted: Thu Sep 02, 2004 16:13    Post subject: If you start a newly installed m23 server there are no managed clients and no entries in the dhcpd.conf. The dhcp server doesn't start without a client in the config file. After the first client is added with m23 administration interface the client values are written to dhcpd.conf and the dhcp server is (re)started. You can ignore the dhcp error message. It doesn't look nice, but doesn't matter too. _________________ Hauke Goos-Habermann - project leader m23 (http://m23.sf.net) - Jabber: dodgerm23@jabber.org Schulung, Entwicklung und Support zu m23 und anderen OpenSource-Produkten: www.goos-habermann.de Auch DU kannst etwas gegen Softwarepatente tun! www.patentfrei.de Back to top gml Guest Posted: Fri Sep 03, 2004 21:07    Post subject: thanks thanks your response. Maybe you write this explanation on the end of m23 installation because for me, I really think that I miss the installation Back to top tyllermills Guest Posted: Wed May 11, 2005 7:59    Post subject: Hy, I have a problem with PXE/ DHCP : -I've installed server correctly. (DHCP is not started : In the syslog i see : "not subnet declaration for eth0 (192.168.0.123) ...") -I've create a client with PXE like this : If the client is OFF, it don't boot automatiquely .... and if I boot the client, PXE search DHCP ..../ et stop after timeout. PS : it the same error with etherboot. I think is normal, because DHCP server don't work ... how configure it ? Back to top tyllermills Guest Posted: Wed May 11, 2005 8:17    Post subject: I have configured DCHP server and start it manually. When the client PXE boot, the error message is : PXE-E53 - "No boot filename received" Back to top tyllermills Guest Posted: Wed May 11, 2005 8:27    Post subject: in my dhcp.conf ... Code: subnet 192.168.0.0 netmask 255.255.255.0 {   range dynamic-bootp 192.168.0.60 192.168.0.70;   option broadcast-address 192.168.0.255;   option routers 192.168.0.1; } and in /var/log/message i have : Code: May 11 12:21:03 serverM23 dhcpd: DHCPDISCOVER from 00:b0:d0:18:8b:9b via eth0 May 11 12:21:03 serverM23 dhcpd: DHCPOFFER on 192.168.0.70 to 00:b0:d0:18:8b:9b via eth0 The DCHP work but, don't send the "filename" to the client. Where is the boot image to the server ? for add line like " filename "/tftpboot/pxelinux.0";" in dhcpd.conf thx Back to top Hauke Joined: 02 Mar 2003 Posts: 1072 Posted: Wed May 11, 2005 9:15    Post subject: Quote: -I've installed server correctly. (DHCP is not started : In the syslog i see : "not subnet declaration for eth0 (192.168.0.123) ...") That's normal if there is no client that should be booted over the network. Quote: I have configured DCHP server and start it manually. You must not edit the dhcpd.conf by hand this will lead to serious troubles. Remove all lines that you have added by hand, delete your client (in the werbinterface) and add it again. Then you should check, if there are firewalls in your network that make network booting impossible. if the dhcpd server is running (ps -A | grep dhcpd) if the client was added in /m23/dhcp/dhcpd.conf Please post the generated dhcpd.conf, if it still doesn't work. What kind of netboot are you really needing? PXE (bootrom), Etherboot (bootrom, bootfloppy), boot CD? _________________ Hauke Goos-Habermann - project leader m23 (http://m23.sf.net) - Jabber: dodgerm23@jabber.org Schulung, Entwicklung und Support zu m23 und anderen OpenSource-Produkten: www.goos-habermann.de Auch DU kannst etwas gegen Softwarepatente tun! www.patentfrei.de Back to top tyllermills Guest Posted: Wed May 11, 2005 11:51    Post subject: I'm sorry, I haven't manip correctly. (I had remove and reinstall dhcp3-server) I have reinstalled m23, and now it's works. The client is added in /m23/dhcp/dhcpd.conf. now I have other pb... describ here : http://m23.sourceforge.net/phpBB2/viewtopic.php?t=101 Back to top Display posts from previous: All Posts1 Day7 Days2 Weeks1 Month3 Months6 Months1 Year Oldest FirstNewest First         READ ONLY FORUM: m23 :: makes software distribution easy Forum Index -> Problems with the server / Serverprobleme All times are GMT - 2 Hours Page 1 of 1   Jump to: Select a forum m23----------------General questions and ideas/Allgemeine Fragen und AnregungenDesired features/Erwünschte FeaturesTips and tricks / Tipps und Tricks Problems with m23 / Probleme mit m23----------------BugsProblems with the server / ServerproblemeProblems with the client / ClientproblemeProblems with administration / Administrationsproblemetesting m23/Test area----------------Tests Debian----------------FAQ Archive----------------Feature requests for 0.5.0/Wünsche für Version 0.5.0Feature requests for 0.6.0/Wünsche für Version 0.6.0 m23/Translator----------------m23/Translator forum  You can post new topics in this forum You can reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum Powered by phpBB © 2001, 2005 phpBB Group